I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi
I have firmware uing SDK 7.1 and SoftDevice 110. There is prepared bootloader for DFU, and update by very old nrfToolbox app works fine. But now I want to update this...
Using the Data Length Extension (DLE) feature in BLE v4.2, two nRF52 dev boards can achieve a maximum throughput of almost 800 kbps. I tested DLE with an iPhone 6 and the...
I am new to nRF ICs.
How to get 32.678KHz clock out from a pin? Is it possible? If yes, from which pin and how to configure it?
I am using 32.768KHZ external crystal fro...
I have designed several boards for the nRF51822-QFAA, namely with/for the Waveshare Core51822 module.
While one is working as expected - namely my "Orchid Lamp" (see links...
When softdevice S110 is used then bonding is not occuring (via nrf connect app to nrf51).but both devices get bonded when s130 is used?In Nrf connect app key matching failed...
Hi,
I have a working project where I use PWM driver with LEDs on the development board. I make use of the d52_starterkit.h where I have the following definitions:
#define...
Hi,
On a system reset, we want a mechanism to stay in bootloader for a short period before jumping in application. This way, if something is wrong in application that prevent...
Hi,
I am using ESB library for nRF52 microcontroller. At receiver i want to measure RSSI value of a packet. I got RRSI from nrf_esb_payload_t structure.
I am printing...
Hi,I have ibeacon (nRF51822) radioland-china.en.alibaba.com/.../long_range_300m_ibeacon_programable_nrf52822_beacons_bluetooth_4_0_tag_chip.html . I want to update the firmware...
Hi,
In my project i would like to save 100 bytes of information in RAM before going to System-off sleep mode.I have tested the example project given in sdk11 works okay.Have...
I am trying to read the battery level on a custom NRF52 board and I am getting a value that is around half of real voltage.
The same code works fine on NRF52 DK ( I was expecting...
I am looking at this example: github.com/.../main.c
In ble_evt_dispatch (line 315), this function forwards an BLE event to all of the modules. By looking at ble_evt_t,...
