I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi Nordic,
I am trying to figure out the relation between a certain page number (say, 0xFE) and the group of addresses that it contains. How can I get this relation?
...
hi,
I am working with nr52832 and SDK 12.1.
I have referred the RNG example based on which I have integrated that code section in my custom application:
rng_generate...
I'm trying to accomplish a communication from the nrf24LE1 to the nrf24L01+. The nrf24L01+ is hooked up to an Arduino UNO. The nrf24LE1 is flashed with the "enhanced_shockburst_ptx_nrf24le1...
6.1.4 Erasing a page in code region 1
When erase is enabled, the NVM can be erased page by page using the ERASEPAGE register or the ERASEPCR1
register. After erasing a NVM...
Hello,
I was testing BLE Heart Rate Collector Example with two nRF52832 devices, one was programmed with ble_app_hrs_c as a BLE central role, and the other was programmed...
Hello everyone,
I have very pesky bug that is leaving me in fits. I have a feeling it is a timing issue, but I am not sure at this point. Here is my issue, and I would...
Hi Devzone.
I've taken the ble_app_hrs example,
and then added the example code from the PWM Driver example.
The PWM module is mostly functional,
however I have a...
Hi,
I'm trying to build a SPI Slave <-> BLE bridge, so that everything received over SPI bus is forwarded on BLE and vice versa. In order for the reverse direction to work...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
I am using IOS nRF Toolbox 4.2 DFU function on nRF51 DK PCA10028. I followed the tutorial here .
Use nRFgo Studio to erase all.
Use nRFgo Studio to program...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
