Hello
Does the green box directly determine which version of the lib to use[ lib_openthread_mtd.a ]? If so, what is the purpose of the red box? If I change the red box to...
Hello,
Context : I use the nrf52dk with nrf connect for vscode and nrf connect for smartphone (android last version). I use the last version of everything.
My code to...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
I'm developing with an nRF52832, NCS v2.6.1 and Zephyr 3.5.99
I've been forcing my MCU into System Off when I don't need it to do anything, then triggering it out of that...
Hi DevZone Engineers,
As I am unable to access my board (Xiao BLE Sense (embedded form) with Nordic 52840 SoC) through the "Connected Devices" tab in nRF Connect, I am trying...
Hello!
I'm new to Nordic Semiconductor and currently developing a project for which I need support regarding the nRF9151 DK . Before placing an order, I would like some...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Hi,
I’m facing an issue with RTT logging on my nRF52840 using NCS 2.6.0. I’m trying to log output from the B0 bootloader, but so far, I’m only able to capture logs from...
Hi, I am trying to set my acqtime different to the max value. And the build throws an error unless i set it to ACQTIME_MAX.
It appears in the header file it needs some other...
Hi,
We are currently in the research and development phase for a new line of IoT devices designed to work over the Matter protocol. After thorough evaluation, we found the...
Hello,
I'm trying to run the BLE LTE sample following this guide on an nRF9160 DK. I get the following error:
[00:00:04.942,413] <inf> nrf_cloud_info: Modem FW: mfw_nrf9160_1...
We are in the process of integrating the Nordic nRF Mesh SDK version 3.3.3 into our Java-based application.
The devices we are working with are pre-configured BLE mesh devices...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
Hello,
I am currently working on integrating the ENC28J60 Ethernet module using SEGGER Embedded Studio and nRF5 SDK version 15.0. As part of this project, I would like...
