Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hello! I occasionally have a crash during the development of nrf52832 (SDK14.2), but this phenomenon is not very reproducible. All the information about the error that I want...
i am able to read data from the i2c device ,,,but i dont know how to send the data through the bluetooth to a central device. i am using the nrf52832 and sdk 15.0.0..someone...
I am just getting started developing a Mesh network around the nRF52840 .
I am confused about which SDK to use for mesh development. v15.0 or SDK for Mesh 2.1.0?
Thanks...
In the Nordic Connect app, firmware uploads keep running even if the app goes in the background or the device goes to sleep. What should I do to run the DFU library with the...
I'm starting with BLE Mesh SDK and have some doubts about their examples.
What's the difference between Light_Switch Client/Server version and Proxy_Client/Server and Provisioning...
Hello,
First time posting, Here are the details of my setup, I would greatly appreciate any help from anyone at this point. I have purchased 2 nrf52 development kits with...
Dear Sir:
I use ble_app_uart example , i want use pwm to driver the FR Port ,Peripheral load. the Peripheral load is pulled up to battery.
when driver the load ,the...
Hi All;
Just a major concern of mine is that SES IDE is so inconsistent;
I can build a solution get errors and warnings...
Without editing anything and rebuilding the...
I have an issue with my board. It resets occassionally itself. When the board is starting by debugger and when it resets itself I can read 0xD in RESETREAS register. What...
hi,
I tried to provision the light example using the nRF Mesh app.
So far, I succedded in provisionning the device but i couldn't set the publish suscribed addresses,...
Hi, I'm using a modified version of the light_switch example to control a RGB led on Mesh SDK 2.0.1. I already managed to control the led by using 3 variables for each color...
I'm designing a Printed Circuit Board (PCB) for and embedded system currently in development. I am using a BL652 DVK from Laird and using SWD programming with Keil uVision...
My project is using QT program and nRF52DK borad.
I want to UART communication with QT and nRF52DK.
#1. If i write "hello" in qt program like below...
===========...
I saw this post for SDK v12.2:
The FDS requires data to be word-aligned
devzone.nordicsemi.com/.../how-to-force-word-alignment-for-fds
Is that still true for...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
