We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
This ticket is the continuation and related to the previous ticket on the matter: https://devzone.nordicsemi.com/f/nordic-q-a/121669/enabling-the-tls-layer-to-get-a-https...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Hi Team,
Excuse me. Where can I find the reliability test reports of the following four models? Thank you!
nRF54L15-QFAA-R
nRF9151-LACA-R
nRF7000-QFAA-R
nPM1100...
Hello,
I'm using the "ble_app_uart" example without a problem. I need to add a timer to this example. For this purpose, I copied the content of the " peripheral_timer" example...
Hi,
I’m working on a project where I need to control a device via BLE_Uart. The scenario I’m trying to achieve is: - I have a network of several centrals und several peripherals...
Hi, I'm trying to use Atomic FIFO in my application, where multiple interrupts of different priorities are trying to read from and write to same FIFO. I couldn't find any...
Hi,
The questions:
When is PB-GATT expected to land in the SDK for Mesh?
What are the best Andorid/iOS example apps to act as provisioner and network...
nRF Connect suddenly can not find the COM port to my nRF Dongle. The same setup used to work fine untill today. I reinstalled the nRF Connect, JLink drivers but it is still...
Hi,
I'm using SDK 15.0.0; nrf52840 DK; IAR(EWARM).
I want to add TWI(i2c) from example in SDK to my project.
But I facing with next errors:
Error[Li005]: no definition...
Hi dear engineers,
I have a strange TWI problem on my production protype which programmed based on the official twi example with softdevice s130_nrf51_2.0.1 and SDK 12.3...
Hi,
I'm trying to schedule few events within the shortest connection interval . Is it possible to shcedule 3 events, 2.5 ms long within 7.5 ms connection interval? Could...
Dear all,
I am using the nRF51822 custom developed board. Earlier it was working fine, but now when I try to connect the BLE with nRF ToolBox APP UART service, the APP...
Hi,
Have flashed an early sd_power_system_off first line in main() when measuring power-consumption...
Now the SWD access seems gone. Is there a trick to get it back in...
Hi, I'm working on a custom board with a nRF52840.
I want to use REG0 and REG1 as mentionned in Figure 13 of the datasheet : with VDDH, and both DCDC. My PCB is powered...
Hi there
I have a NRF52 Dk already and it had been setted as master.
The log might contain the specific advertisement channel power or how much packets has been sent...
Hello,
I want to send 6 bytes of data over BLE. I will set a timer for this purpose. When there is timer interrupt, the data will be send.
What I wanted to ask is that...
