Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi:
I just got an nRF52832 development board, I have ran the tutorials using Eclipse and I was able to run the blinky example.
I am now trying to get a BLE application...
Hello,
As far as I understand previous versions of DFU BLE bootloader implemented a timeout so if DFU is not being used and an app is present it will run after a few time...
Hi,
I want to OTA firmware upgrade of STM32 (External MCU) using nRF51 through Android App on BLE. STM32 and nRF51 communicate on UART.
Please any one suggests how to...
My project based on nRF52832 and SDK is 12.2. I need to support alert notification(service UUID 0x1811) client profile for mobile device, I just build and download the nordic...
I've been seeing occasional failures of my application which I now believe are due to a bug / design flaw in the app_timer library module.
The problem is due to a race...
Hi :
I have problems ,for gpiote interrupt hanlder can be hanged up by softdevice. In normal use ,I should pull up sck pin of my private ADC chip for less than 10us and then...
Hi,
I'm using the SDK 12.2 with the sd 132 3.1.0, and actually I'm trying to send two separate advertisements wich I'm swapping every "radio notification event", but I...
I am working on modifying the ant+ sdm example to hack my treadmill. Got the example running and talking to my Garmin watch and the display simulator. All of that seems straight...
This problem didn't appear every time when I upgrade firmware. If I restart my app again, sometime the SDK can works well.
Anyone can help? I'm use SDK in Android, Legacy...
Hi,
I am using nRF51-DK and nRF5_SDK_12.2.0_f012efa. I have programmed Proximity example from the SDK to the Development Kit and was able to successfully program the DK...
I have a function with a return value in the time slot, after the function is done inside the time slot signal callback function, I want to use the event callback function...
Hi
We'd like to set the pairing timeout when using the function sd_ble_gap_authenticate(conn_handle, p_sec_params) . The reason for this is that we are setting the connection...
(/attachment/182b723590b3c447267d5aed62b5405f)hi, i want to work on PWM to controll the vibration coin frequency for certain time period and also to change RGB values of LEDs...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
