Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
Hi Nordic
I’m working with the nRF5340 and nRF21540 for 802.15.4 and would like to know:
The expected RX sensitivity estimation for this combination.
Any reference...
Hi, How do we send a byte array using mosh? From the documentation I can see: sock send -i 0 -l 100000 This specifies the socket and the length. But how is the actual data...
Dear Nordic Semiconductor Team and Community Members,
I am currently working on an nRF54L05 project where I aim to use only the primary slot in MCUboot due to memory constraints...
Hello team,
We are using nrf54l15 platform using NCS 3.02 SDK.
When advertising the MAC address changes in two following conditions
1. After every reset
2. After connect...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
/* Copyright (c) 2012 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided...
Hello,
I am trying to program my BMD-300 using the NRF52-DK, below are my connections
BMD- 300 ---------> NRF52 DK
V Vtg
SWDIO SWDIO
SWDCLK SWDCLK
GND GND
The BMD 300...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I am able to compile blinky with my SW tool set up, however, when I try to compile a more complex example (ant_broadcast_rx_pca10040_s212) I get issues with the...
Hi,
I hope is not a double post. I am doing a throughput evaluation with my custom board and an app that is based on the Nordic's Android UART app through NUS service and...
I am trying to get the ble_app_uart project to build in Eclipse for the PCA10036 nRF52 board. I have followed the Tutorial titled " Development with GCC and Eclipse" and successfully...
Hello,
i am stuck with this, trying to write to flash using pstorage module. Below is my code.
static void pstore_cb_handler(pstorage_handle_t * handle,
uint8_t op_code...
Hello,
I have downloaded the Hardware Files of nrf51822 smart beacon kit. But I Cant open the Altrium Designer Files (pcbdoc. files). Do u know how to open it or a program...
Hi,
I do test my project one central connect to 4 peripheral(HR and CSC).
and I put the memset(&m_ble_db_discovery,0,sizeof(m_ble_db_discovery)); err_code = ble_db_discovery_start...
Hi,
I use nRF52832 and SDK12.2
The Project is ble_central_and_peripheral and the link define is like below
#define CENTRAL_LINK_COUNT 4
Here will connect 1 HR device...
Hello,
Is it a good practice to modify SDK files?
I mean, do you use SDK as integral part of your project and feel free to modify it, or do you try to avoid it and just...
Hello,
We have connected Nordic+ MPU 9250 and able to read sensor values through UART display, but we wanted to do some excercises and read values, but it's not possible...
hello guys,
i am new in nrf micro-controller. I want to get data from my smartphone and want to write in memory of nrf51822 through BLE. when written process in memory is...
I'm a newby. I'm troubles understanding how to send command to ble. my band have own protocol like this :
if you send 'AB02FF7180' to ble means your band will shock 5 times...
We have a application that use the ADC of nRF51822 to detect a variable resistance (schematic is attached). The current passing through the variable resistor should be around...
