Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi.
I'm using the arm_sin_f32 function to generate an array of sine wave values. However when this function gets called the softdevice crashes.
I've included:
#include...
I've been trying to chase down some of the engineering samples of the nRF52840 for a prototype with no success from distributors here in Japan (have tried Digikey and Mouser...
Hello,
I know that the NRF_TEMP peripheral is a restricted peripheral and should be accessed with the sd_temp_get function when the soft device is running. Heck I even...
Does the NFC library globally disable interrupts at any point? We're trying to track down an issue where our code occasionally misses an I2C event during NFC read/write.
Hi all,
when I try to send 6 bytes of 0xFF, the last bytes change. I use SPI in mode 3. I use the NRF52832 on a custom board using SDK13 with sd v4. See the following screengrab...
Keil4 compiler in the compiler C and assembly of the mixed code, the error content is: Branch offset 0x00000388 out of range of 16-bit Thumb branch, but offset encodable in...
This function contains a lot of tags that need to jump, but at compile time there are these errors.
this is ARM compilation and C mixed,How should this error be handled?...
Hello, I am trying to develop on the NRF52. I have the development board and have been spending time with the SDK and documentation. I understand how the GPIO should work...
Our nRF51822, S110 device uses concurrent advertising (iBeacons) when connected to the central. Our customer would like to have a variable tx power on the advertising packets...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello
I adapted the ble_app_uart with twi functionality.
Therefore I included the "app_twi.h" which includes the "nrf_drv_twi.h"
But as visible in the picture, the "nrf_drv_twi...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
