Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
In my project I need two UART's. One UART will be used for UART over BLE communication and another one will be for Connecting other modules with nRF52 board. So is it possible...
I built and downloaded the softdevice and app to the nRF52 board. Then I used nRF Connect Android app to connect to it. It seems to be connected as the LED1 is steady. But...
Hi guys,
I installed the latest nRF Sniffer software and use Wire Shark 1.10.14. My JLink driver is 6.12A (I'm not able to access any of the earlier drivers). The command...
We have received few nRF52840 preview DK. And one among them has a white sticker label which says 2016.49 and all others have 2017.14.
Should we be using the ones with...
hi, i was just wondering whether the app_timer works like a function or like a thread.
e.g. lets say i got my mainloop
while(1)
{
start_timer(...);
//DO SOMETHING...
hi：
i flashed bootloader_serial_xxAC.hex and s110_nrf51_8.0.0_softdevice.hex with nrfjprog. and flashed flash_page.hex, then update app using mesh serial, the app run well...
hi :
I want storage different size in flash.How can i do it?
I can write like this?
param.block_size = 16; //Select block size of 16 bytes
param.block_count = 1; //Select...
I have been analyzing the current consumption of my nRF52832 dev kit today using both a multi meter and an oscilloscope with a resistor. I'm not sure what I exactly did that...
HI All,
I wonder if someone can help me out. I would like to send serial data by modifying the 'simple_coap_server' main program. I added the following header 'app_uart...
Dear,
is anyone of the Nordic customers here using unit testing in their nRF52 project and would be willing to share an example project/their setup? Would be awesome. ...
Hi,
We are range testing BLE using the DK-52 with an external dipole antenna connected via the u.fl connector. We are using the DK-52 + packet sniffer software on a laptop...
I tryed to port the dfu secure bootloader sample of sdk 13 to eclipse managed project. after a few hours, i finished it. compiling and linking went fine but the filesize is...
Cannot connect to ATECC508A through TWI with NRF52832. Tested with nRF5_SDK_12 twi_master and deprecated twi_sw_master. It was working fine only with NRF51822 nRF5_SDK_12...
