Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
Dear nordic employee
My 52832’s GPIO control the external 32mhz crystal‘s power，
when the 52832 work in the sleepmode ,I cut the 32mhz crystal'power
then when I want...
Hi I have a problem with TWI (the slave part), that is, we can only receive on nrf52840 8 bit, there is someone who knows how to do so you can receive 16 bit, we have taken...
Is there possible to get timer period shorter than 12us with nRF51 and SDK 14? "timer" example with PCA10040 works correct, but with PCA10028 not. When set timer period lower...
When I go to build any of the nRF SDK BLE examples, I get linker errors that app_error_handler was not found. I now copy-and-paste a boilerplate version of that into the code...
Hello,
I'm currently trying to OTA update the firmware of my nRF52832 DK, I use the SDK 12.3.0.
I loaded the BLE Secure DFU Bootloader in the DK, it's advertising as...
Hello, i use nRF5_SDK_12.3.0_d7731ad. I took this tutorial https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and according to...
Hi, Guys,
I am using nrf52832 for our product. Recently I updated stack and sdk from s132v2/sdk12.1 to s132v4/sdk13. However, I see a new characteristic under Generic Acess...
Hello,
I'm trying to run the example ble_app_uart using nRF52840PDK and iOS 11.
The device appears as Nordic_UART but when I connect, nothing shows up. The following screen...
Hi! Compiler errors are popping up when working on nrf_drv_rtc.c while log is enabled for this nRF module. I see that the problem is any log statement that contains EVT_TO_STR...
Good afternoon,
I have been doing some tests with the nRF SDK for Mesh v1.0.0, and have a question regarding it.
I'm using a fw based of the Light Switch example, to...
By using the DFU to transfer an updated version of the application, The nRF Connect tool pop-up tip:"upgrade succesfully". But the version of application mostly is still older...
Hi all,
I have been looking for the DFU library in objective-C, without any dependency manager such as cocoapods or Carthage (we cannot use them in our solution), but...
I found the thingy hardware files and I was wondering if one can buy the flexprint antenna from you or if you can connect us to your manufacturer.
We are planning to use...
