Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
At first i have tried the simple uart code from nRF52 where i could send the AT commands properly and UART communication works fine between nRF52 and GPRS module.
Next...
I use a development board with nrf52832 xxaa, BLE demo from SDK works. But I created own board but with nrf52832 xxab(less ROM and RAM) and changed configuration in IAR project...
Hi,
I want to use hardware ECB encryption and decryption in 52840.I had tested the demo from nRF5_SDK_13.1.0\examples\crypto\nrf_cc310\aes\pca10056 . However,i can't find...
When using the APP_TIMER in SDK14 I am having a problem with the application stopping.
I was using the APP_TIMER to flash LEDs and watch for timeouts in SDK13. when porting...
in the sdk_config.h there are plenty of definitions, where "31" is used as a non-valid PIN value
This is destructive if you want to use p0.31
For example:
If one uses...
Hello. I want to use the same pin on nrf52832 for wake up and system off, however I have some issues, like sometimes it doesn't wake up or it is needed to press button few...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Edit: I'm using the softdevice S110, 8.0.0, Nrf51822 chip, Keil uv5.12
Edit #2: Added more detail and revised certain description.
What's the problem?
My program...
Dear partner,
1) Our custmer want the spec of S140, I cann't find that on the inforcenter. can you give me one?
2) By the way i want to know where is my mypage case...
I want to have every node carry a copy of the sensor data in every other node and pass these around on update.
Should I use ANT FIT or FS? What makes mores sense?
As the...
Hello,
How can I detect how much RAM is still free on the heap during runtime, without a debugger attached, just from within the application?
Cheers
Trax
Hi
Can nRF52840 PDK support UART buad rate 921600/1000000 correctly?
I am testing UART with below example for our product development:
nRF5_SDK_14.2.0_17b948a\examples...
Hello, I have problem during dfu otau over ble connection. I use linux version of the nrfutil - my OS version is Linux-4.9.0-3-amd64-x86_64-with-debian-9.1 In some cases i...
I am trying to enable SPI in spi_config.h but SPI3 is missing for the nRF52840.
I need DCX functionality, and from the OPS for nRF52840 it looks like it is only SPI3 that...