Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi. I'm using nRF51822AC, SDK12.2.0, S130.
The size of "s130_nrf51_2.0.1_softdevice.hex" in SDK is almost 300KB.
But chip's flash mem size is just 256KB. It's bigger than...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
Hi, I use the nRF52832 board (PCA10040 v1.1).
Before creating a custom PCB that uses nRF52832-QFAA, I chose
Q22FA12800025 FA-128 32 MHZ 8.0PF (load cap = 8pF)
and ...
This should not be a sudden my PCA10040.
Jlink are probably going to have failed.
It does not appear in the USB Jlink to appear as Atmel.
Is there a way to recover...
I am doing a project about nrf51822 smart beacon kit and a person has give me this link: infocenter.nordicsemi.com/index.jsp
to download the firmware and hardware files...
Hello,
I develop a BLE central device based on nRF52 (with the newest connectivity firmware and SoftDevice with API v3) and the pc-ble-driver in version 2.0.
Since my...
Hello Everyone,
I am working on nRF51 I need to save data with timestamp (current date and time).
Is there any example code is available so I can set current time and...
Hello,
Recently read about FIDO’s U2F authentication protocol for NFC and Bluetooth smart.
https://fidoalliance.org/fido-alliance-equips-u2f-for-mobile-and-wireless-applications...
hello everyone,
I am doing a project about Ibeacons. I need to make a selfmade bluetooth smart beacon (excuse me for bad English). I found a schematic circuit design of...
Hi all,
I am trying to get an Android Nexus 5X app to work with an NRF chip, and facing some problems, specifically with writing to a characteristic. Really hope to get...
