Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
I am getteing a -12 error when trying to access a open/create a file using littlefs and a fs_open command on a nrf5340 custom board.
The filesystem seems to be mounted fine...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
From SDK 7.2, we have the following definitions:
components\drivers_nrf\pstorage\config\pstorage_platform.h
typedef uint16_t pstorage_size_t; /** Size of length and...
There was something in the webcast yesterday about a Nordic nRF52 roadshow/tech tour/worldwide series of events.
I hunted around the nordicsemi site but didn't find anything...
hi,
i am working on ble project where i am trying to develop a project with master(mobile phone)-bridge(acting as master and slave,nrf board)-slave(nrf board) .i use the...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off all modules except the RTC timer.
So, after shutting down the radio...
Hi,
How could i implement Just work pairing method in my "ble central and peripheral" example. I modified project to suit my need, and everything works fine, untill i try...
I am working on a ble project ,'ble_central_and_peripheral",s130.In this project the device acts as master and slave. It connects to the slave only if the address is predefined...
I may be missing something. I am trying to generate a square wave from a GPIO pin in a BLE application (SoftDevice 8.0). I tried libraries (nrf_pwm.c and nrf_pwm.h) in this...
Why does the nRF52 only have +4dB output when most competitor chips are atleast +6dB (some up to +10dB). I understand that the RX has been improved by 3dB for a better overall...
Is there a way to know that there is no more data being received via UART?
One solution is, of course, to start a timer every time a byte is received via uart_evt_handler...
I am using read characteristic to read data from from a characteristic. The characteristics range from 2 bytes to 32 bytes in length. The time to read the data using IOS,...
For those of us who were not invited to Norway to try the nRF52 over the next two days....
When and how can we get our hands on a nRF52 development kit?
For example, ble_advdata_set() wants to insert company identifier and a "00" in the last byte of the response packet. Are these required, and if not, how to use the ble_advdata_set...
Hi there,
One quick question about updating Beacon configuration, including UUID, major, and minor. For development, we can use our APP on the phone or Master Control Panel...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
