Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Do you think I could update PCA10001 V2.0.0 just by replacing the nRF51822 chip? I have more current chips lying around, and with a little rework I could be able to switch...
When writing a post in this forum, I found it somewhat nice to have a preview before I do submit.
Even for questions, answers, comments and pm. May it possible to enable...
Hi
Is the generic attribute primary service 0x1801 added by the soft device?
Bluetooth standards say that the service changed characteristic is optional. I am using...
Hi sir
According to nRF51822 RM v2.1 session 12, there are two high frequency clock: the 16/32 MHz crystal oscillator and the 16 MHz RC oscillator. For nRF51822 BTLE application...
I know the question has been asked, but a few months has passed,
but hopefully to get some new update now.
devzone.nordicsemi.com/.../nrf51822-dk-module-as-master
devzone...
Hello,
i try to implement a simple timer interrupt on TIMER1 using one of the CC registers of the NRF51822. Here is my code:
void init_timers(void) {
// Start 32...
Hi,
I have 2 questions regarding this topic:
Which specific J-Link lite mode do we get from nrf51822 Development Kit? Is it the 9 pins model or 19 pins model?
...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...