The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi all,
I'm looking for some advice on what hardware to buy for my next project as I'm not clear from the specs if existing self-contained solutions do what I need.
I...
I have software on my PC with an NFC reader attached, that connects to my nRF52 devices, reads the NDEF tag, modifies it, writes it back, then reads back the modified value...
Hi,
I've been trying to get the button events from the nrf52832 where FreeRTOS is enabled.
https://gist.github.com/gpgabriel/f070e39f335da8579e9a577b44109237
The 2 function...
Hi, We are testing the dfu ota example for the PCA10040. In our application we have some default values and settings are stored in the RAM. nrfutil is unable to generate the...
Hello,
I am using the Thingy app for ios as reference to read my own temperature sensor. However, I am reaching a point where I get stuck.
I cannot understand/find where...
Are there any limitations when the central is connected to 20 peripherals at the same time? Is there a minimum connection interval (ie, can I set them all to 7.5ms?).
Hy everybody,
I'm trying to implement DFU bootloader in our custom board, starting from the "bootloader_secure_example", where I just changed leds and button pins in order...
hi,
i am doing nrf_mesh_dfu example with nrf_sdk_for_mesh v1.0.1.
so far i am able to generate device public_key and private key by following instructions .
and also...
Hi, I get a hard fault when I try to add an own UUID to the softdevice S132. I'm using Eclipse with GCC compiler, Rigado BMD350 eval board with the nRF52832 chip on it. As...
Hi Nordic DevZone ,
I wanted to enable the new feature Advertising Extensions in the example application light_switch and see how it works, but unfortunately i can not...
Hi,
i am evaluating the use of the nRF51822-QFxx for our product and made good experience with the nRF51-DK. Now, i would like to layout the custom pcb and i am not sure...
Hi
The definition for nfc_t4t_ndef_rwpayload_set() is that it takes buffer_length parameter.
And the comments state "buffer_length Length of buffer (maximum writable NDEF...
Hello there,
I have developed a board with nRF52840 and a sensor. My hardware and tools setup is:
SDK: nRF5_SDK_for_Thread_v0.10.0_e1c3d11
Thread version:OPENTHREAD...
Hi, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it using eclipse. Here is the code:
Someting is not working and...
I am able to disable the reset function of P0.21 by erasing UICR register and undefining CONFIG_GPIO_AS_PINRESET .
Still i can't set P0.21 as output and set it to 1.
