Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I use Adafruit Bluefruit library and developing code to run on Fanstell BT832.
Up to know i have been able to compile several examples and run it on the NRF52 DK board....
Hello! I am new to the Nordic and Bluefruit enviroments.
I am currently working on getting a scan response request from the scanner to the advertiser and have the advertiser...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
Hi all,
i development a FW with a low power and when i measure the power consumption using a nrf connector on evaluation board i have 2 ua, and it's ok. Now i have the some...
So I can see the "API Reference" documentation on the UART driver in the info centre, however this is all very low level and I am going to waste hours going through all this...
Are there any changes required to run the Sample Bluetooth Low Energy (BLE) applications from nRF5 SDK v14.2 when migrating from nRF52840 IC Rev A to Rev B? I have followed...
Hi,
I am using the nRF52832 on a custom PCB and I am interfacing it with a flash memory chip through SPI.
I am testing the SPI communication using the spi example (nRF52...
Dear Sir,
1. The HFXO crystal can be with load capacitance 12pF? or 8pF is better?
2. According to the datasheet, "17.1.1 64 MHz crystal oscillator (HFXO)"
there is...
Hello,
we have two custom boards with nRF51822.
We use NUS.
If our pakets under 23 Bytes everthing is fine ....
If we want to sent paket with 140bytes, the central...
Hi!,
I've made a custom board using Taiyo EYSGCNZWY bluetooth module, to be used as central in a project. To use this module, several changes have to be made in the clock...
Hi,
I am using nrf52840 to verify a signature using RSA and cryptocell c310.
I get error 0x07 when I try SaSi_LibInit();
My rndContext and the buffer are both declared...
Good afternoon.
I have bought a "nRF51822 Bluetooth Smart Beacon Kit (nRF6930, Rev 1.3.0)" this is the first time I work with this, docs say that it has installed softdevice...
On the current version of the nRF5 SDK we could only use up to 3 instances due to the hardware limitation on the Engineering A of the silicon,
nRF52840 Engineering A
...
