Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hello,
I do know that it is a lot of information here in dev zone about this topic but I need a confirmation from a Nordic employee. We had a disscusion at workplace wheter...
I've just read the BLE Mesh documentation, very informative, but I still have some questions related to the concept and implementation, which are:
Can a device toggle...
Dear all,
I have made a nRF52810 module according to the reference circuit in datasheet and connect it to my PC via Segger JLink & SWD. Only 1 out of 3 notebook I tried...
Is this chip for sale yet? I see dev. kits, but still 28 week lead time everywhere. We were talking about adding it to a product, but the owner is shooting me down because...
Hello NORDIC community,
I am performing a BLE throughput speed test via an example of streaming a buffer of 2500 bytes per second: This says a sending frequency of 19 Kbps...
i used SoftDevice s332,and download the example:\examples\multiprotocol\ble_ant_app_hrm
i find that using android device can connect pca10040 ble well,but use ipad or iphone...
Hi
We are working on a product using NRF-51822 chip. I am new to Nordic SDK and want to know how to use fstorage to save data into flash. Following is code. Sometimes data...
Hi,
I would like to build a project with functions below.
Support BLE uart service
Support CLI with uart interface for the communication with terminal, like TeraTerm...
Hi All, I am building a wireless MIDI controller using the BLE nano v2.0 from RedBearLab.
MIDI is a protocol to control software musical instrument, therefore latency needs...
Hello everyone,
I try to modify SDK 14.2.0 S132 ble_app_template example with Segger Embedded Studio, but I got an error about uart. All uart functions appear to be "undefined...
It seems that the version of the soft device used in the mesh sdk does not match the version of soft device SDK that I can download, and the version used in the mesh SDK has...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
