I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I know the question has been asked, but a few months has passed,
but hopefully to get some new update now.
devzone.nordicsemi.com/.../nrf51822-dk-module-as-master
devzone...
Hello,
i try to implement a simple timer interrupt on TIMER1 using one of the CC registers of the NRF51822. Here is my code:
void init_timers(void) {
// Start 32...
Hi,
I have 2 questions regarding this topic:
Which specific J-Link lite mode do we get from nrf51822 Development Kit? Is it the 9 pins model or 19 pins model?
...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
Hello,
currently I am thinking about the proximity concept. The following scenario is given:
We have a Display that shoud lock/unlock a Device
We have a iPhone...
I used SDK 5.1 and S110 6.0, I dowmload the project ble_app_ancs to nRF51822 DK. I try to connect it to iPhone 4s (which run on IOS 7.04), when I click 'pairing', the led...
Device: NRF51822; BMA250E
Description:
When I read BMA250E via I2C without BLE protocol, commnucation run well.
And if there is no I2C commnucation, BLE protocol can...
