Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
We are working with SDK 15 with the HRS freeRTOS example. we did some modification to the advertising modes so that we advertise on fast mode for 1 minute and after...
Hi,
I'm using nRf52832 with SoftDevice S132 V3.0.
I found that I can exclude a bluetooth channel from the map by function sd_ble_opt_set .
But how can I tell that a...
When I compile the project (nrf5_SDK_for_Mesh_V2.0.1) exemple: Light_Switch....... there is an error that appears
#include "boards.h" --> (no such file or directory) Why...
I'm using SDK mesh v1.0.1 and nrf51822 S130 for mesh application. Light switch example is working fine. Now I want to add a twi sensor in server side. My doubt is in mesh...
Hello,
First, the current of the advertising frame was too high (around factor 2) and I have switched on the DC-DC to correct for that by inserting sd_power_dcdc_mode_set...
Where could i get the apk of thingy 52? it's hard for me to log on the Google play to install it because my phone didn't have GoogleServicesFramework, could anybody send me...
I am working on RTLS project. In beacon i am advertising battery life and temperature along with minor number and RSSI . I am merging battery strength and temperature in major...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* android ver.8 smartphone with nRF Connect
I have implemented the...
Hello I'm using a macbookPro 2016 which only has usb-c and I can only connect the dk through a usb hub.
I have already installed the nrf5x-Command Line Tools for OSX but...
Hello everyone, i'm currently doing a project with nrf52832 and i just came across a problem. I configured 3 pins as output, then i set 2 pins to high and 1 pin to low. But...
I would like to implement UARTE.
· Nrf 52 · SDK15 · S 132
The big advantage of EasyDMA is that it does not issue interrupts for each byte received. In nrf 51, "app_uart_get...
Dear Sir/Madam,
Normally battery level notification is only one byte. But I need send byte array of 58 bytes through battery level notifications in my project. I have to...
I am developing my code in a custom nrf52832 breakout board. My code was modified from the example "ble_app_uart".
I find a high current issue with UART. The current is...
Hello,
I am trying to evaluate the NRF52832 on a custom board and i will design the antenna according to your NRF52 Thingy:52 design. I am quite a newbie about RF&Antennas...
