Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
Hello!
I'm pretty new to BLE and Nordic, and hope that someone can give me some good advice.
I'm working on a project were I have 2-4 sensors, each connected to a nRF52832...
Morning,
I ve try to flash the hex pca10040 from the examples/ble_peripheral/ble_app_hrs without success, with the flash seems ok, i can t see the device.
So as i ve...
I found this comment in fds.h as function header for fds_record_write()
* Record data can consist of multiple chunks. The data must be aligned to a 4 byte boundary, and...
Hi guys,
i was testing the connection speed from android in conjunction with advertisement time to see what will work better in my production code.
The result were:
...
Hi, Forum.
I want to make uart_bootloader without softdevice. for this, I want to prepare keil project.
I tryed this but I have some problems.
Basically,
My bootlader...
Hey there!
I am trying to switch from Keil to Eclipse.
I have followed several tutorials on this website ( like this one ) and I can easily create new eclipse project...
Hi,
I use the SDK9.0.0 S130'DFU project in the parth of pca10028\dual_bank_ble_s130\arm5_no_packs\ for testing.I found S130'DFU code is different compare to the S110 of SDK6...
Hello,
I am using MDBT40 ( www.raytac.com/.../MDBT40 spec-Version A5.pdf) in my project. Also I am using arduino IDE to create .hex file for MDBT40 using this reference...
I have the nRF52DK board and I am using that to reprogram the Sparkfun breakout. However, initially, I was using the Sparkfun Beefy UART device to flash the nRF52832 to begin...
This message appears :
Field 'BLE_GAP_CONN_SEC_MODE_SET_OPEN(&hrs_init.hrs_hrm_attr_md.cccd_write_perm)' could not be resolved
but the build and flash were successed...
I have enabled Timer 2 with 31250Hz frequency. I wanted to call an interrupt after 10ms, ie 312 ticks for the timer. But the interrupt is not getting called, I have spent...
Hi Folks,
I have a quick question about the Beacon kit. I'm working on a project that is going to use Windows 10 Hello companion device framework to build a Windows Lock...
is there a tutorial for Ble ECG program and configuration using nrf52832?
I want to make integration from heartbeat sensor to nrf52832, make nrf52832 connect to computer...
