Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi! I'm working on HID mouse example on SDK 13.0.0. I'm supposed to use this as a low power media button control. I've done a few modicifations on the code for power optimizations...
I know that few companies choose to use NRF528001 with a separate microcontroller like Fitbit.
I would like to know why would they do so instead of using an NRF52 chip that...
Hey,
I am using a nRF8001 with a STM32L051 as an application controller.
After resetting the nRF the RDYN pin goes low, as expected. Then I'm setting the REQN line LOW...
Hello all,
I have a Nordic Thingy 52 board, and I have download the Thingy 52 SDK, I can debug it successfully.
But after I debug it , or download it, the board runs with...
We have an application with FreeRTOS. If we do not initialize softdevice, the freertos interrupts tend to come in at a very very slow rate. I know that softdevice does clock...
nRFgo Studio displays a "Enable reset pin" option on the nRF52 DK but does not display this option on our custom hardware; we use a Segger J-Link for programming the custom...
Hello,
I would like to know the CALIBRATEOFFSET function in detail.
Could you disclose the part of source code on this CALIBRATEOFFSET function?
Best regards,
Kiyoshi...
Hi,
In production line, I was supposed to do BLE test using DTM with UART interface and MT8852B from Anritsu.
However, the antenna is specifically tuned for plastic...
Hi,
i was about to solder my PCB that contain an nRF52832 and i've noticed that i didn't have C9, C10 capacitors.
C10 is the 1uF decoupling capacitor for the 1.3V regulator...
Hi, I'm using nrfUtil 10, which is a bit old. I'm trying to generate an init packet for DFU but the tutorial was for newer versions of nrfUtil only and a lot of commands appear...
I tried to compile the sd card example from the fatfs library. But it didn't work.
Can anyone tell me more about this errors?
NRF_BLOCK_DEV_SDC_DEFINE(m_block_dev_sdc...
NRF52DK (PCA10040) - SDK14 - Arm GCC (using Eclipse) - S132 5.0.0 Soft Device
I had a custom service set up in SDK13 using the tutorial here .
I am migrating my project...
Using nrfjprog version 9.7.2 on Windows 7 Professional. Just discovered that when .hex file is read-only, nrfjprog fails.
>nrfjprog --verify --program app.hex Parsing hex...
