hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hello,
I'm working on a custom GATT service which has only one characteristic that support notification. The code has started from the ble_hrm service and it runs on a thingy...
Hello,
After having read the documentation of "nRF5 SDK v15" and "nRF5 SDK for Mesh v2.0.1" it is not clear to me which PHY layer it uses at the end.
In the documentation...
Hello,
I am going to use nRF52832, but I have nRF52840 DK, can i use this bord for developing project on nRF52832. Is nRF52840 compatible with nRF52832 in software and hardware...
Hi
I assigned one LED Signal to P0.08 pin in nRF8122 CFAC package as per pin assignment it shows as digital GPIO
But in Firware wise when checking the LED Does not glow...
Dear all,
maybe I‘m missing something, but I know there are OTA DFU client libraries for Swift, ObjC, Java and Python.
But it looks like there is no DFU lib from one...
I was using nrf51822 ,S110 and SDKV10 i had created custom services and its working fine, But when moved to nrf52 DK and S132v5 SoftDevices and SDK version 14.2.0 . same services...
I would like to develop some app to be able to use nRF51 dongle on PC. Is there any good example codes to start with? My plan is to use pc-ble-driver-js and Electron and found...
Hi,
I am starting to look at using 2Mbps Phy (and eventually coded PHY). I'd like to add the functionality where my device will automatically switch PHYs based on some metric...
/**@brief Function for finding out whether a peer ID is in use.
*
* @param[in] peer_id The peer ID to inquire about.
*
* @retval true peer_id is in use.
* @retval...
Hello tech support!
I am using the built-in SPI to transfer the data. Also, I adopted the "timer" example in the SDK for handling the SPI transfer.
However, it seems that...
hi
I want to design Nodes for asset tracking. These Nodes will be spread out in a building. A moving object will have a BLE -Advertosor. The Nodes will detect Moving object...
Hello, I'm using the nRF51822_QFAA chip on a pca20006 board. I downloaded sample code from the offical site. Installed sample code nRF51822_beacon_firmware_1.1.1.msi. I use...
SDK: 14.2
64-bit Segger Studio 3.34b
PCA10040 Rev. 1.2.4.
64bit Windows 10
SD: S332
I'm trying to add the bpwr Tx profile to the ble_ant_app_hrm_pca10040_S332...
