hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello everyone,
I remember doing a project with PCA10028 board and S110 SDK a year or a year and a half ago. Now i want to do another project but all my materials which...
Hello,
I am writing this question in reference to this question . I was asked to be more specific about my question by my colegues. I do understand that this is a duplicate...
Hi,
I checked the flash_fds example. I could not tell the address it tries to access to. Is there any way I can find the address? Can I limited it to a certain address range...
According to this article, https://www.nordicsemi.com/eng/Products/Bluetooth-5, it appears that the nRF52 should be able to support standard BLE at 2Mb. However when I look...
Hi Nordic
I am using sdk 14.2.0 version and s332 soft device. Now I have completed the bicycle speed cadence code that works with ble_ant. It worked well as I wanted. But...
hi,
I am a fresher .I am asked to do the communication between nrf51 D K and moblie phone( nrf connect app). Can anyone provide me a sample code and required documents to...
Hi
I am using SPI to talk to an LIS2DH with an NRF51822. I have merged the SPI Master example with the ble_app_rscs example and as soon as the ble advertising begins, my...
nRF Connect has no serial ports to connect to. I've looked in /dev. No unusual tty or cu devices listed. I've checked the forums. Mentions is made about Segger link and "...
Board: custom board
Mesh SDK: V1.0.0
Softdevice: S132
IDE: SEGGER Embedded
BLE: nrf52832
When I test the steps specified by “Interactive PyACI”, I can control client...
Hi,
I have spent a couple of days trying to find formal documentation on how to update the nrf SDK. I am currently on 11 (as keil pack installer states the version of...
Hello everyone, I come from the 8bits MCU world and I'm used to program my chip with a debugger like Atmel-ICE. But with 32bits MCU I'm a bit troubled to program nRF82832...
I'm using the IoT bootloader from NRF52 SDK 14.2. When the bootloader has nothing to do and starts the main application, the FDS calls all fail in the main application. When...
We're using QuantumLeaps and want to send a message each time a character is received on the UART command line interface transport layer.
Where in the SDK source code would...
