Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi!
I am working with PCA10040 (nRF52), s132 and SDK 12.2.0.
I am using the example experimental_ble_app_eddystone.
I have configured one slot as TLM, so it reports...
Hello,
We're using JLinkExe for production programming. Is there an equivalent of the nrfjprog --erasepage command for JLinkExe?
I'm looking for the equivalent of
nrfjprog...
Hello,
I feel like this question has an answer similar to this question, but I can't seem to get it working devzone.nordicsemi.com/.../
I am using the nrf51422 chip...
Hello,
I bought a SainSmart display which fits on the PCA10028 development board. This display is a 16x2 character display with a HD44780 display contoller (I guess).
...
Hi,
i am new in nrf51822.
i want to make a pin as a external interrupt pin, whenever it get high to low pulse it will call in ISR.
here i am unknown how to write an ISR...
hi,
i have downloaded code to nrf52 BLE module using nr52 DK with VTG,SWIO,SWCLK connections. but here i am unable to display the log for nrf52 ble module. is it possible...
Hello, I got the solution for my previous errors, but now I'm facing new error, that now when I compile my code it gives error like invalid command name "nRF52"
ac2...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
The system hangs when doing burst write reg.
MPU9255 can work fine if all writes are ...
I'm having a strange issue with getting SPI running through the transaction manager whilst running a S140 softdevice (SDK13 w/ nrf52840 5.0.0-2Alpha - I know there's a newer...
Hi,
See attached photo for layout placement of the trace antenna.
Altium PCB File : 108-0013-01 PCBA MAIN.PcbDoc
Background :
This is a design for a wearable...
Hello,
I am using SDK 11.0.0 and attempting to integrate the BNO055 IMU into twi_sensor example and then connecting the IMU data over BLE via ble_app_uart.
I successfully...
Hello,
I have two devices sharing an I2C bus. These devices are the MAX86150 and the MLX90614. DMA is being used. I2C is running at 100 KHz.
After initializing both...
Hello,
I'm currently working with sdk 11 on nRF52832.
I'm trying to acquire 20 value from SAADC every 10ms during 300uS.
I think that the rate is too high because...
Hi , why I can't have an update of my bootloader ? Here is the script I use to generate the .zip file :
nrfutil dfu genpkg --bootloader Bootloader.hex Boot.zip
The...
