SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hello everyone
I was not able to find any explicit statement regarding the use of the TWI_APP with easyDMA on the nRF52 series and SDK13.0.0.
I checked the examples...
Hello guys,
I am currently looking at the recommended schematic QFN48 with internal LDO setup and I have a few questions (sorry, if they are silly, I am a newbie).
...
Hi, I'm working on an extremely space-tight design and need some clarifications. It is an nRF52832 QFAA chip with a Johanson 2450AT18B100 chip antenna.
Up to this point...
Hi,
I would like to use higher dBi antenna instead of the DK pcb antenna. Can I say the pi-network before J1 (measurement point) probe is 50ohm? Hence I can just remove...
I am trying to control another BLE device with nRF52xx. For controlling the device I need a terminal for connecting, disconnecting and switching on & off a sensor. I have...
I am using NRF52DK and trying to debug an SPI transfer, using SEGGER_RTT.h to print. However, printing of the logs are not consistent. Some debug lines do no appear in the...
Hello,
The only semi-official information that I can find regarding the differences between PCA10040 1.1.0 and 1.1.1 DK boards is this post . It suggests that there are...
I recently ordered two NRF52840-PDK and a Segger J-Link Base to program/debug the boards.
Then I just read that the development kit have a J-Link OB included, or I could...
Hi.
I wonder that how to setting continuous modulated output mode for nRF24L01P.
I see Appendix C - Constant carrier wave output for testing in datasheet.
But there is...
