Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello Nordic team,
I'm developing firmware for a custom board based on the nRF54L15 , where the LEDs are connected to GPIOs on port 2 . These pins do not support hardware...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi, would like to understand what scenarios a clock stability better than +/-40ppm would be needed in a BLE setup.
i.e. channel sounding, and similar. I mean you can get...
Hello,
I plan to use uart1 for serial port development based on the binary protocol. I will receive bytes using the interrupt method. But when I send bytes (such as FAFBFC...
I have a custom board with nrf5340 and want to run the radio_test sample on it. I have been able to compile and run the sample using the uart serial terminal, but I'm not...
Hello everyone.
i want to configure the TX power of the NRF radio in BLE advertisement and connection of the NRF54L15 MCU. I am using the nrf Connect SDK version 2.7.0....
I am studying Lesson 6/wifi fund_1ess6uexer2 and I can run the provided code normally.
（academy.nordicsemi.com/.../） But I still want to control whether to send packets...
Problem - while working in a project where VSCode does not have visibility to the nRFConnect SDK folders, but where the project includes project-specific KConfig files, the...
Hi,
i am under Windows 11 using the latest VS code extension (2025.4.106).
How should i use https://docs.nordicsemi.com/bundle/nrf-connect-vscode/page/reference/settings...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
