Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I think the idea of limiting the behavior of a model to states is very wise, but due to my limited understanding in this matter, I find it puzzling as to what happens...
Is it possible to use the NRF52832 UART in half-duplex single-wire mode, by assigning TXD and RXD to the same GPIO, setting the GPIO drive to disconnect '1' and using a pull...
I am running the example under peripheral\pwm_driver on PCA10040, and SDK 12.2.0. Using a scope, I measured the period (from rising edge to rising edge) on one of the LEDs...
In my project, the softdevice I used was S110
I hope that some of the data can still be retained after OTA updates,
in the Bootloader program code:
#define DFU_APP_DATA_RESERVED...
Hey togehter,
has anyone succeeded setting up a connection between ST-Link and nRF52832?
I connected the pins (GND, SWDIO, SWCLK and second try with GND, SWDIO, SWCLK...
Hi,
Please let me what is the beacon layout of nRF58122 for scanning beacons in region by using following method:
BeaconManager.getBeaconParsers().add(new BeaconParser...
I'm using and NRF52 with S132 and SDK13.0. I'm using Keil as my IDE.
My application acts as a central for smart phones to connect to and also acts as a peripheral to conect...
Hi, I'm a mechanical engineer, an industrial engineer and have a master's degree in control of the dynamics systems. I never get the change to work with ARM architecture before...
Help, what UART output pins that gather all information from the various sensors in the NRF52832 thingy52, to integrate with Raspberry or Arduino, thank you
Hello Community,
I am trying to implement a whitelist in my central device but when I type ble_gap_whitelist_t I had an error of compilation becuase ble_gap_whitelist_t...
Hi,
My first objectif is that the Micro:Bit consumes less than 2μA without the BLE. I read that the Micro:Bit program was not powered if the Micro:Bit is powered by the...
Hi everyone,
I am writing a program in Keil whereby I have to send a large amount of data through BLE notification in real time. The program works by having two timers...
I want nRF52832 to be a central device which will take an input from nRF51822 (peripheral device). Also, Is it possible to make two nRF51822 talk to each other?
Hi,
I having an nrf52832 board and using gnu arm, nrfjprog to program the device. i reading data from two different sensors using spi and TWI in two different codes. now...
