I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I am working on secure OTA in my custom Board which is having nrf51822.
I had done secure OTA successfully with SDK 12 but when i am trying to update the code using...
Hi, I want to measure Round Trip Time (RTT) varying data rate
However, when using coded phy, the RTT shows extremely long time
Using 1M or 2M with connection interval...
Our nRF52832 software detects the arrival of characteristics via writes from the Central and reformats the contents and sends them out in a UART message.
I've built an...
Hello, I want to create a simple example code with the leds ws2812b from neopixel from github.com/.../nrf51-neopixel. I need help to build the code.
Regards.
I'm converting an SDK 14.2.0 project to SDK 15.0.0 using the legacy functions and ARM GCC. It compiles OK but linking is failing.
The verbose output appears to be the Make...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
Hi,All,
I am using nrf52832 as a slave, the SDK version is 12.3. I set the connection timeout to 10s as follows
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(1000, UNIT_10_MS...
Hi,
I'm having an issue to connect a Galaxy samsung Tab A to my ble device.
Each time i ask for a connection i get the same error.
I already succeed with others phone...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
