Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
I just got nRF52 DEVELOPMENT KIT and NRF51822 BEACON KIT.
Can you tell me that where I can find the reference design for them and what could be the good starting point...
Hello, I am trying to program an BMD-300 using the NRF52-DK on a custom board,
The BMD300 is powered by the NRF52DK
BMD300 -> NRF52DK
SWDIO -> SH_SWDIO (pin 4) on...
Hi,
I just read IoT-MQTT example and have almost exactly the same problem but with the Publisher.
I am running a PI with Raspberian 4.4.34-v7+. I have installed mosquitto...
I am running the SDK12.2.0 ble_app_template peripheral example with RTT Logging enabled. The example seems to be running OK, but it logs: APP_ERROR:ERROR:Fatal with the ID...
Hi,
I am using NRF51822 to complete an application of multilink on one central . I tried to modify the central_link_count definition to 9 instead of 8, then I stuck on the...
Hello,
I am new on nRF51 and i would like to have a function to read the rotary position of motor in any rotary direction by adding a codewheel and a two channel reflective...
Hello,
I am trying to implement wake on motion functionality of MPU9250 with nRF52.
I am writing below sequence code for wake on motion configuration:
void MPU6500_StartMotionDetection...
Hi DevZone
I want to make a little beacon app, that advertises on channel 37 then waits 700 ms, advertises on channel 38, waits 700 and advertises on channel 39.
The below...
HI,
I wan't to read sensor data from ADC. So i use nrf_drv_saadc_sample() .
On Arduinos i usually call value = analogRead() and after that i process the data. But here the...
Hello,
We need to add custom data to advertise packet. As I understand we can use Manufacturer Specific Data. But to do this we need to get our Manufacturer ID from Bluetooth...
I have the following code for a custom service UUID and a custom 128 bit characteristic ID. I get a error of no memory available in our_char_init while adding the 128 bit...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
