The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I can't figure out why I can't send ADC values to the NUS service via BLE correctly. I should be getting hex values that convert to something like 0 or -1, since the ADC pin...
Hi all,
I'm currently learning on how to build bluetooth connections with a device from an app. For that I downloaded the iOS version of the nerf Toolbox app, as my chip...
hi
I am using nRF52 DK
Loaded Blinky Peripheral
I Connected this nRF DK to Com Port and Started Master Control Panel
But the Start Discovery Button is Disable. Please...
Hi,
I have an issue wherein once OTA update is complete through nRFToolbox (Toolbox says " Upload Complete") the Device does not reset and shows that it is connected to...
I am in the development stages of developing a ble application with the nrf52840 nordic chip.
I have come to realize the increasing difficulty of debugging this chip only...
Hello,
I made a custom board based on nRf52832, and I am using SDK 14.2
When I use a slightly modified version of the ble_app_uart example, I see it with nRf Toolbox,...
Hello,
I'm trying to configure 2 serial ports for a custom board with nRF52840 chip, but when I try to instance the second UART "NRF_SERIAL_UART_DEF(serial_uart1, 1);" the...
Hello,
I have an nRF52840 Preview DK, I would like to try the advertising extensions you introduced in the new released SDK.
My Goal is to make an application which send...
We're using a combination of the ESB library/example code and the USB CDC ADM example code to transfer data from one 52840 dev kit to another system via a 2nd 52840 dev kit...
I'm trying to build the gazell_dynamic pairing example for the host from the 14.2 SDK with GCC and I keep getting undefined references during the build process. I've added...
Hi,
I have modified nrf5-ble-mpu-data-ready-interrupts from nrf5-mpu-examples, the example works as expected. I have modified it a lot.
Now when I try to reconnect, it...
Hi,
We're running into a frustrating and tricky to debug issue with handling interrupts on the nrf52832. We have an active-low interrupt to pin 28, that is activated periodically...
Hi,
I just saw the errata for the nRf52840 Rev 1 and it seems Anomaly 197 ( DCDC of REG0 not functional ) and 202 ( Device does not start up in high voltage mode ) make...
Hello everyone
first if all, im not an expert in PWM, but doing my best to understand everything
I have successfully created and tested a project using the pwm_driver...
