Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Nordic,
I am using the BLE Shield v2 and the Arduino Due board to transmit accelerometer/gyro data to an Android tablet app that plots this data. I had this working fine...
First I noticed that nordic has already updated the andriod nrf toolbox app to use softdevice v7, which allows updating the softdevice, bootloader and application.
The...
Hello all,
I'm working on a library for NRF24L01+ and PIC micro.
Unfortunately there is something wrong. On the receiver side, the micro correctly detects that a packet...
Hi,
I am knew to BLE and I was able to ran succesfully the blinky project. Now when I load the soft device on and then try to download the hr example if says "Flash download...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I develop an application with the nRF51822 circuit. It is detectable with my smartphone, but not with a computer that has a Bluetooth 2.1 device. Is it possible to...
In the comment of this post , Marc Nicholas wrote:
Doesn't that require SWO to be implemented? (Which is not on the Nordic part).
Is it true, that SWO isn't available...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm trying to understand how pstorage allocates storage.
PSTORAGE_FLASH_PAGE_SIZE is fixed, that's the actual size of a flash page and thus a basic unit as you can only...
Hi, I am trying to change the beacon data.
I changed Beacon UUID already, but I can not find where can I change device name.
I guess I need to change the gap_adv_data...
Hi,
I am upgrading to SDK 6.0.
What function should I use for retriving the whitelist data?
SDK 5.2:
//err_code = ble_bondmngr_whitelist_get(&whitelist);
//APP_ERROR_CHECK...