void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi sir
According to nRF51822 RM v2.1 session 12, there are two high frequency clock: the 16/32 MHz crystal oscillator and the 16 MHz RC oscillator. For nRF51822 BTLE application...
I know the question has been asked, but a few months has passed,
but hopefully to get some new update now.
devzone.nordicsemi.com/.../nrf51822-dk-module-as-master
devzone...
Hello,
i try to implement a simple timer interrupt on TIMER1 using one of the CC registers of the NRF51822. Here is my code:
void init_timers(void) {
// Start 32...
Hi,
I have 2 questions regarding this topic:
Which specific J-Link lite mode do we get from nrf51822 Development Kit? Is it the 9 pins model or 19 pins model?
...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
Hello,
currently I am thinking about the proximity concept. The following scenario is given:
We have a Display that shoud lock/unlock a Device
We have a iPhone...
I used SDK 5.1 and S110 6.0, I dowmload the project ble_app_ancs to nRF51822 DK. I try to connect it to iPhone 4s (which run on IOS 7.04), when I click 'pairing', the led...
