Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
The NRF51822 series manual describes that an external LC filter is required to operate the buck converter. The reference design shows 1.001 uF of total capacitance to ground...
i try to test Low Energy Applications Using nRF51822 with application note ( nAN-36 )
in chapter 4 : led button example, build and install success~!, but, not running application...
when I use app_uart.c code with FIFO, uart is ok, but I always encountered a out of memory ( always return NULL from malloc )
How to monitor / determine memory / RAM usage...
Hi,everyone
I have trouble in debugging the "device_firmware_updates" example. Here is my development environment:
Keil-MDK :v5.1.0.0 and v5.11.0.0(an other PC).
SDK: 4...
I want to make a nRF51822 as broadcaster and peripheral role concurrently. It should have continuous broadcasting advertisement data under accepting connect-requests to notify...
Hi,
Looking at pstorage related code, it appears that it handles data copy from RAM to Flash.
Can I use pstorage functions to move data within Flash? I want to implement...
HI All,
We want to use UART RXTO event to detect UART packet boundary.
So we propose to add one entry APP_UART_RXTO to app_uart_evt_type_t in upstream sdk to sync.
...
I can not understand how works READY register in SPI master:
after first byte transmission READY sets high, i set READY low and send second byte, but READY never sets high...
I can upgrade the firmware by MCP on air ,But there are one conditions:
reset the device while holding down the Enter Bootloader Mode button or a invalid application is present...
Hi,
I am running (and reconfiguring) ble_app_lbs (LED + Button BLE app) example as a kind of start off project for me. I am actually trying to figure out where I can control...
Hi,
When i increase the global buffer , i got this error.
if i reduce buffer size and add few more characteristic , i am getting same error.
How can i use Flash memory...
Hi All,
I started with example ble_app_multilink_central for S120 from sdk 6.1. I then started stripping the application to get a barebones central. I removed app_trace...
What I`m using:
-nRF51422 EK
-Keil v5
-nRFGo Studio 1.17.1
-SDK 6.0 and 6.1
-SoftDevice S110 v 7.1
-Applicatio: ble_app_hrs
I first Programm the SoftDevice
Softdevice...
I've done a lot of reading on the forums about this topic and done a lot of trying myself. I haven't had much luck and it seems like most everyone is in the same boat.
...
Hi,
On my ble application, I want to keep after wake up reset the previous value of a variable, I tried using sd_power_ramon_set(0x000f000f) to keep on all ram partitions...
