In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi All.
I made my PCB with nRF51822 and achieved around 150 Feet range (LoS). My target is to calculate a approximate distance (in Feet) from RSSI values.
I did a field...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using nrf51822 evaluation kit with ble_lbs (Led button sample) profile, I need the USB dongle source code for ble_lbs (Led button sample) profile because I...
Hi,
Is it possible to change the advertisement parameters of a beacon device without connecting to it?
(ex: major,minor value & interval)
Is it OK if our beacon product...
I use ble_app_uart demo of pca1001 and my SDK version is 5.2.0. I want to use APP_BUTTON_INIT to handle a button event. So I changed the buttons_init(void) like this:
static...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
Hi everyone, I don't have the nRF51822 yet, but still want to get familiar with it as much as possible before I get to buy it. I was looking for a description of the functions...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Has any managed to connect a Windows Phone 8.1 device to NRF51?
BLE is "definitely" supported on Nokia Lumia:
Nokia Support
But I am unable to pair with either SD 5.1...
