Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I see from the 51822 PAN sheet v3.0 that item 61 still shows Rev 3 QFAA package devices as potentially having problems with LO leakage. We are in production with R2 QFAAG0...
Hi,
I am trying to run the ble_app_hrs_c, using:
s120_nrf51822_1.0.1
nrf51_sdk_v6_1_0_b2ec2e6
PCA10006 + nRF6310 + nRF6350
After the compilation of the...
I need to port ssd1306 library for oled to nrf51822.
so i tested following code. but it's not worked.
main(){
if (!twi_master_init())
{
return false;
}
ssd1306_init...
I am using the GCC DFU project provided by Nordic on GitHub ( devzone.nordicsemi.com/.../)
I altered the main.c to trigger to DFU mode based on the contents of the GPREGRET...
I'm trying to connect a camera module ( OV7670 ) to my nRF51822 EK. The camera requires an operating current of 18mA. If i were to connect the 3.3V rail input for the camera...
I have code that uses two GPIOs to program an NRF51822 via SWD mode. This code all works fine and suceeds in programming the device.
What I would like to do is get the...
How can I relocate or manage the transition between the bootloaders interrupt vector map and the applications interrupt vector map which will be at different addresses in...
Hi !
I'm completely new into programming this device.
I downloaded the nAn-36 source from Github and I'm trying to make it work on a PC10000 dongle.
The code stops in the...
Hi,
I wonder if there is any way to disable the Rx FIFO so that I don't have to fill it to generate an event, since I need exact timing for every incoming byte.
Also,...
Hi, I am trying to connect N51422 server to anther vendor's client... the devices always disconnect after 30 seconds of connection.
I found that the reason of the disconnection...
I have seen this question asked on this forum in several ways but none of the parameters match up to my specific case. I am getting this error when I try to run the example...
Hi,
I load the s110 softdevice (I tried many versions 5, 6 and 7)
When I load my app on the SOC using Keil and the nrf_xxaa_s110 (256) target, the app doesn't run.
I'm...
Dear Nordic Developer Zone,
I have implemented a real-time-clock using application timer which is based on the on-chip real-time counter on NRF51822.
A concern of mine...
I'm trying to get the Nan-36 example working on my PC10001 board and I'm having some trouble. I've tried using both SD110 version 6 and 7 with appropriate (I think) memory...
