I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I will come back to the discussion in (because it is in state "Verified Answer" I opened up a new one) :
https://devzone.nordicsemi.com/f/nordic-q-a/55197/nrf52832...
Hello All,
I am looking for a simple example which can handle GPIO interrupt on an event. Is there anything of that sort? Or the API is documented somewhere?
I am using...
i have been trying to interface the imu sensor gy-80 with nrf52840dk
but an error of on the reference main
and the thumb set instructions no memory set errors are comming...
Hi all,
I am doing some development on nRF52840 board with PCA10056.
SDK version: nRF5_SDK_15.3.0
Softdevice: s140_nrf52_6.1.1_softdevice
Testing Example: nRF5_SDK_15...
Hello
in our concurrent radio application using timeslot API there are failed assertions from time to time (10min - 10h).
Message is as above.
Stacktrace and system...
Hi,
I would like to know how much memory my application is consuming. We are using NRF SDK-15.3 version.
In View menu there is option Memory Usage, but when I build in...
Hello,
I am trying connect with the nRF52840 dongle from my android phone using nRF Connect App. The nRF52840 dongle as peripheral and I am using nRF SDK 15.20 and s140_nRF52_6...
Hi,
I have a mesh device (door sensor) with cell battery powered.
When triggered, the device power on, do mesh stack init and start mesh stack, publish a mesh message...
Hello all, is it possible to wake-up the device from deep sleep using cap sense.
How reliable is the ADC cap sense, Im little confused as some people say CapSense is not...
There is an "error" in the Mesh 4.00 friend.c:friendship_alloc(..) function, when allocating a new friend with PollTimeout greater than 2147 seconds. The LPN allows you to...
Hi,
Working with Uart + DMA on the nrf91 board, we see two issues:
1. With baudrate of 115200, we get an overrun error after getting ~6KB of data.
2. Sometimes we do...
I am trying to develop a simple uart driver based on the nrfx_uarte driver but I get compiling errors (see below).
All I have is a simple uartOpen() function for now...
Hi,
Greetings!
I am trying to develop a device called as " Gateway ", which can receive SIGmesh messages and update/send those messages to cloud server and vice-versa...
