Hi.
I have been investigating how to use GRTC and LFXO for LFCLK with nRF54L15DK. In my goal, I would like to make the Intermittent application with sleep and GRTC that...
I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Currently, there is a project. The situation is that the master nRF52840 communicates with the cloud server through the GPRS232 module, the slave nRF52840 communicates with...
Hi,
I tried to create a custom server in using server setup of nRF Connect v3.3.0 but when I tried to apply my custom server on my device, the software bugs instantly. ...
I want to modfiy the code in the example ble_app_ancs_c to read the internal flash with fstorage. But after I set APP_TIMER_CONFIG_USE_SCHEDULER to 1, the operation of fstorage...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ). The problem is: My provisioner node cannot Receive RSSI message of a node...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
My custom function for saving is:
I call the function using below...
This error always stop the "mqtt_simple" application.
I have tried modem versions 1.0.1 and 1.1.0, SDK versions v1.0.0 and v1.1.0 and added this code to system_nrf9160.c...
I have an Android application running with RxAndroidBle library and I want to change it to Nordic-Ble-Android library. I'm not that good with Bluetooth and the actual version...
Hello, i'm new in BLE and i would like to know, what is the best way to read and write 200-300 parameters of my product via BLE from a phone?
Possibility 1 is, to create...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
Is this correct by populating the record as such?:
And to read...
Hello,
is there any tutorial on how to send commands to the Thingy52 from an Android app (like the Thingy52 app or nRF Connect) to start the RTC clock (and then read/clear...
My 52833DK is apparently bricked. I get the message "Could not find core in Coresight setup. Abort debug session” When I try to load code (IAR) into the board. It was working...
Hi
I'm trying to understand the files outside the main program. The files that are at the samples path. Like "CMakeLists.txt, Kconfig, proj.conf, sample.yaml etc". So from...
Hello.
I have a issue about saadc input range.
First, using 52832, SDK 15.3.0 S332 Softdevice.
I using ble ant both and 2 rtc time and gpiote also used.
my goal is...
Hi guys!
Testing a little bit with the nRF511822 and Power Kit. After a little testing, I changed my application a bit and wanted to flash it into DK (via Keil) and it...
