I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
The product description says the nRF2460 has "Support for external PA". Since this chip does not present separate TX and RX RF terminals, and no apparent TDD output logic...
Hi all,
My goal is to use all the advertising data for beaconing, and also be connectable with the NUS service.
In order to save space for the beacon data I would like...
I have a nRF24LU1 USB device that I want to configure to make communicate with a nRF24L01 device on an Arduino Uno. I tried to install nRF Go Studio and J-Link Segger driver...
Can anyone tell me whether it's possible, within the SDK (or otherwise!) to create a grouping of GPIO pins? Essentially, a design change means that we want to combine what...
Does anyone happen to have 3D models of the PCA10040 and PCA10056? I found the Altium files, but, being an Eagle user (and not having an Altium license), I was wondering if...
Hello,
I'm using nRF52 SDK12.2 "ble_app_uart_c" project as a "Central", and the target device is the "Peripheral."
Test Steps:
Using putty sending message(with...
How can i initialise all four channel of pwm1 using pwm library.
i need to initialise one channel for one purpose and other channel for different purpose.
whenever i am...
Hi,
I just tried the example from
github.com/.../nrf52-mpu-easydma-using-gpiote-and-registers
And they are working like a charm. Now I want to change the example...
In the on_ble_evt(ble_evt_t*) function from the ble_app_template, I added a case of 'BLE_GATTS_EVT_WRITE'. In it has the following code:
case BLE_GATTS_EVT_WRITE:
{ ...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
Hello dear Nordic Semiconductor!!! I took your wonderful Thingy:52 everything was great until I wanted to build a project based on your Thingy: 52-SDK. I have nrf52840 pdk...
hi, i am having a doubt. now my nrf 52840 is acting as a peripheral. it is advertising some packets and my mobile is acting as a central and receiving the advertising packets...
