Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I'm trying to create a local network between an nrf51-DK and a mobile phone, android or iOS. The main goal is to be able to get TCP/IP connection between the nrf5x...
I am writing firmware for a BLE Nano device using the Nordic SDK 8.1. I was having problems where my device would suddenly stop printing to UART and stop trying to bond with...
I'm trying to set up a ble mesh with 3 servers and 1 client on an nrf52 PCA10040 dev kit. Upon debugging, I'm getting an error that says: '64, APP_ERROR: C:\Users\sesa463145...
I am using a NRF52-based platform and have BLE code based on the ble_app_hrs_c Hear rate monitor system.
Having set up for scan, I see many device (we have a lot of beacons...
After migrating from sdk 13 with buttonless dfu based app I meet follow error:
my app get FATAL error after exactly 3min. I guess it something related with power down mode...
I have a 3 channel setup on my SAADC module, which I sample according to a LFCLK timer. I notice after the first called to nrf_drv_saadc_sample() and receipt of the ADC results...
hi,everyone!
we use the example
"nRF5_SDK_14.0.0_3bcc1f7\examples\ble_peripheral\ble_app_uart\pca10040\s132"ble_app_uart,
we also defined
"#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
At the very end of this post from Nordic Info center I am doing the exact example at the very end.
infocenter.nordicsemi.com/index.jsp
This is the start to do a transmit...
Hello
I'm trying to track lost packets in a connection by showing the sequence number of each packet received. Specifically it's about an application that sends new measurements...
Hello sir,
I have develop product on nRF52832 DK and now i using custom nrf52832 board Here . I want to continuously on my device with BLE advertising continuously no sleep...
Hi there,
In my SDK12- SD132 NRF52 app, I'm running NUS ok, and I want to add two more services. So, I made this changes at ble_stack init:
ble_enable_params.common_enable_params...
I am trying to add an extra service from an exiting nordic example code:"experimental_ble_app_blinky" into another exiting nordic example code: "ble_app_hids_keyboard".
...
Hello,
I'm encountering a very strange problem while attempting to run an fstorage fs_erase operation on my peripheral device when the central is connected. This is on...
Hello,
I want to make a device that use a Zigbee SoC and a nRF51822 for BLE, and I want to make it in the same board, that imply to have two antennas in the board.
I...
