Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I want to use battery service in my beacon for that i have tried two examples of sdk14 on nrf52 dk
1)ble_app_hrs
2)ble_app_proximity
in first example ble_app_hrs...
Hi,
I am nrf52832 SDK14 .
Can you provide a simple example of IRK implementation to resolve the peripheral address in SDK 14.It will be helpful to get insight of it. ...
Hi,
Do you know why I get a warning : Unable to allocate memory for relay packet. ?
I am trying to mesh 2 servers and 4 clients. with client capacity 3 for each server...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
Hello,
I'd like to send 16 bits data over ble instead of 8 bits
gatts_value.offset = 0;
gatts_value.len = len;
gatts_value.p_value = data;
err_code = sd_ble_gatts_value_set...
The call to ble_x_handles_assign() is not uniformized on all the examples. It's sometime call from on_ble_evt() or/and from x_evt_handler() .
From the doc on the function...
What shoul i do? 0 erro with code
SEGGER J-Link GDB Server V6.20d Command Line Version
1. JLinkARM.dll V6.20d (DLL compiled
Sep 29 2017 16:44:59)
Command...
I am using S120 Softdevice, with bunch of different type ble tags(peripherals). written a code to connect multiple tags at a time and doing a gattc read to fetch the battery...
I have a technical issue I am facing while doing development with Nordic NRF52840. I have an application which I am sending command though virtual com port using CDC ACM USB...
Hello everyone!
I am learning with nrf52840 MCU and SDK version 13. When I read the example. I see one line:
SVCALL(SD_BLE_GAP_CONNECT, uint32_t, sd_ble_gap_connect(ble_gap_addr_t...
Hi,
I'm developing a project based on nRF52 and utilizing NFC for my master's degree. One part of the project will be a beacon with as small PCB layout as possible. That...
Hi,
Often when I try connect BLED112 dongle to bluetooth module BMD-300 by command:
ble_cmd_gap_connect_direct(DeviceMAC, gap_address_type_random, 60, 76, 100, 0); ...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
