Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We have a custom board solution with an BLE module from Laird, that uses nrf51822 IC, as a gateway. Code was written in Keil and we used SDK v 8.1.0. Originally we didn't...
According to BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part G page 2248
Exchange MTU procedure is initiated by the Cilent, and only be initiated once.
But by looking...
Hi,
I'm trying to add the peer manager to my project, following the guidelines at infocenter.nordicsemi.com/index.jsp
I've copied the peer_manager_init() function exactly...
The pm_evt_handler routine handles the event PM_EVT_CONN_SEC_FAILED and lists the following text as comments:
case PM_EVT_CONN_SEC_FAILED:
{
/* Often, when securing...
Hi Community,
I have nrf51822 module and use it's ADC. I had 2 AAAA batterys to supply power. But found 3V regulator consumption over 100ua. It's too much with sleep mode...
Hi,
We are trying to learn how to use the python bindings with the nrf51 dongle on an application for a windows PC.
We got as far as installing the pc_ble_driver_py, but...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.1 on total 2 boards(1-client (own nrf52832 board) and 1-servers (dev kit nrf52832 with pca10040...
Using Windows 10 I get an error when I try to export the graph from my PPK 1.1.0 to any Image File (PNG JPEG etc). SVG and CSV export works well.
Python shows this error...
Hello, Thank you for helping me to interface the PCF85176 (40 x 4 universal LCD driver for low multiplex rates) with Nordic nRF52 development kit board. I need to write the...
i have a few question, i bought this " www.skylabmodule.com/.../".
if the device has a sample code loaded?
where are the example codes for the device?
i want connect...
Hi everyone,
I recently acquired a nRF52832 Breakout Board from Sparkfun. I have been using it for a few weeks now and everything was fine. I was programming it using the...
I use DFU function to update APP. and when i execute the flash write operatin in APP,then afer the dfu operation,bootloader can not jump to the APP. it keeps in bootloadr...
I am using nrf52832, SDK14 and sd 132.5.0. I want to disable SAADC after measuring battery level then enable again when I want to measure it again like in this post . When...
