Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
HI,
I am using nRF51822 S130, SDK12.3.0
I created private key for application code and public key for bootloader. Just few days ago, the zip file can upload to the device...
Hi,
I use NRF51822 + S130 + SDK12 platform, my device work in CENTRAL mode, I want send data to peripheral every 10ms, code like this:
while (1)
{
while (m_free_tx_packet_count...
Hello,
I am currently working on nRF52840PDK baesd project, where I want to use BLE using RIOT OS. So, please can you provide any example for RIOT OS based BLE or any details...
Hello all ,
I am using nRf52832 and i found PWM conflicts with Softdevice: We were able to create a sample PWM application which works fine independently. When we merge...
I'm developing a system which consists of 1 or more remotes (3 or 4 max) that have to communicate with a single host.
I need a fairly simple protocol, low power optimised...
hello all,
I am using nRF52832 and blow is my querry.
Implementation of power ON/Off feature:We are able to put the board to system ON low power and System OFF low...
I am using radio notification to change every advertisement packet. Here is my code:
static void on_ble_radio_active_evt(bool radio_active) {
if (radio_active) {
advertising_data_init...
Hi all!
I'm trying to move to SDK 14 with some project.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 23..70 all works good.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE > 72 exception happens...
Hello, I am investigating the possibility of integrating the DTM functionality into our app (which uses the softdevice) to allow us to use a single image for production testing...
Hi,
I am using the SAADC example in SDK 12.2.0 together with SoftDevice (S132, v3) and its working fine without any problems. As a modification, I want to uninitialise...
After calling sd_ble_gap_connect() at an arbitrary time, how does the central actually connects to the peripheral?
Assuming the client probably listens only at certain times...
Hi all,
Is there a way to change the UART pins configuration to bypass the segger jlink debugger on the nRF51/52 devices? I would like NOT to use this debugger chip for...
I am trying to receive a string of 708 characters via BLE. As BLE cap a maximum of 20 bytes per transmission, at the mobile app side I break the data to be send every 20 characters...
Hi All.
I wanna to continue Advertising during peripheral connection due connectable ADV prohibited if Peripheral connection established for nRF52840.
Is it possible to...
I'm trying to print a 20 byte array over uart before sending it on BLE. My array contains:
{0x34, 0x12, 0x00, 0xFF, 0x00, 0xFF, ..., 0x00, 0xFF}
However when I try...