Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
Hi all,
I have written an adv demo myself, and once Bluetooth is connected to the customized board, the following problems will occur,
but it works fine on 54L15DK....
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Hi,
I am currently developing on the BL54L15 Ezurio development kit with the Nordic chip.
I am using the Nordic v3.0.1 SDK and toolchain with the new manufacturer board...
Hi,
I am Currently running BLE Mesh with nrF5340DKs, I refer all nodes as Cores but 1 as Master, Master receives and Stores data as well send data to PC Serially for further...
I am using an NRF52840 DK along with an NRF7002 EK, I have gotten the default wifi scan sample working with these boards. However, my next steps is to use custom pins on the...
Hello,
We see there is a HID BLE keyboard example in NCS and it works great.
So we are checking if we can using it or re-develop it for a BLE Braille Keyboard to fit...
I'm developing with an nRF52832, NCS V2.6.0 (happy to update to a newer SDK if it gets me the functionality I need) and Zephyr 3.5
What I'm currently doing is having my...
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the nRF Connect...
