I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello,
We're using SDK v14 and nRF52. To pass some data between reboots we're using the general purpose retention register. However, it seems like it's impossible to call...
I try to transfer the codewords from nrf51822 Dk board to a dongle board, while the dk board is PCA10028 and the dongle board is PCA10031, when I change the port numbers and...
I'm new to the nrf51822, i was connected led to one of the gpio pin of nrf51822 development board. In 1 minite i want to toggle led 20sec and remaining 40 sec in sleep. After...
The SDK 12.1.0 documentation for the FDS library says the following:
FDS_THREADS: If set, the FDS module can be used by multiple modules at the same time (for example...
Hello,
I am trying to measure the current consumption.
i could cut the SB9.
and i use analog discovery and measured!!
the picture is shown in below.
gyazo.com/b9f5607148cd9415ea7d1ee6ac644373...
Hi
I have tried to make use of the FDS for storing data and encountered this behaviour.
The required setup of the sys_evt_dispatch() & fs_sys_event_handler(sys_evt) are...
Hi,
were are looking forward to redesign our PCB. The nRF51822 will communicate via I2C which sinks up to 3 mA and 15 IOs will source the maximum rate of 15mA. Additional...
Hello,
I implemented a function to add characteristics to a service, but I'm having a problem when I add notifiable characteristics. I pass a set of flags to my function...
Hi,
I set a debug LED on as the very first thing I do in main. Randomly (sometimes 2 in a row, sometimes 1 in 100), sometimes my debug LED never comes on and no code is executed...
Hey Everyone,
I am new to nordic development. I am really used to programming with easy environments like the Arduino. I have seen some examples using the printf() command...
Use the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_library routines, now can output two lines of PWM, but want to two way different PWM phase have...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
Hello.
I am trying to turn off ACK in the example "esb_ptx". I have tried this in both SDK 12.2 and 14.0.
I try to turn off ACK like this:
static nrf_esb_payload_t...
