Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi,
Scenario:
Two nRF52832DK boards on a table, approx 20 cm from each other, +4dBm output power.
Payload length is ~60bytes.
Running at 1Mbps gives me less than...
Hi,
assuming I have an IMU sensor with 3 different interrupt lines. And I want to start a TWI DMA transfer for each interrupt line in parallel. Is this possible since there...
Hi all,
We are starting new project, the aim of the project is control street lights through web site by using gprs connetion.
The key requirements of the project is...
Hi
I finished preparing the nrf52832 board to use ppk and measured it with ppk.
I am trying to repair the nrf52832 board.
However, I do not understand the contents of...
Hello,
I'm porting the nRF8001 SDK to STM32 using HAL (CubeMX). Communication seems to run fine, however, the setup stops with CRC error. See abridged the logical output...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
Hello, i'm using a nRF52840 on a PCA10056 and want to wake up from __WFE() with a minimum delay. When i'm using the debugger, i achieve a low latency but without the debugger...
Hello All,
We are working with one of the customer, where he is asking for range 200 meters between 2 nrf52Dk(nrf52832) and he want us to prove the same using two development...
I am trying to use the cryptocell in the bootloader (bootloader_secure_ble) for verifying dfu packages, but fails in signature verification for the same dfu package, same...
Hello,
I am designing the NRF52832 based board.Specifications of capacitor in reference design is as follows:
0.8pF, NPO, 5% tolerance
But with my vendor these two capacitors...
I am designing nrf52832 based board. In matching, 3.9 nH inductor is given.
I have selected the componenet with following specifications :
Specifications of inductor...
Hi Everyone
I am using nrf52832 development kit , sdk 14.0.0 with iar and i am trying to merge the ble_app_buttonless_dfu and ble_app_uart code.
I have done the changes...
Hello guys.
I am able to save an array to flash memory unfortunately I can not save a struct in flash. I am referring to this question Save struct to flash . However I...
Hi,
I'm a beginner in programming Nordic uC and I would like to know how to enable the watchdog in my application. Are there particular functions to call?
Thanks!
Hi,
We have a prototype application which requires an NRF52 based peripheral to be inside a metal cabinet and to connect via BLE to a central while maximising the link...
