Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am trying to set up UART communication between the nRF9160 and nRF52840 that are found in the Fanstel BLG840XE. Currently I am sending a test string of "abcd" from the nRF52840...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hi ,
I am using nrf connect 1.2.0 dk. I am now testing the https client example.
However, I always get the connection fail error as belows.
Provisioning certificate...
Hi:
I want to send pictures and voice.So it needs to be faster.What should I do?
I use nrf52832/sdk16.If nrf52840 is used, can it reach 2Mpbs?
Measurement example:nRF5_SDK_16...
Hi there,
Here is what I'm trying to do. I'm trying to use the 52832 as a badge to be used by people in order to report the zone the person is in using a ble mesh network...
HI:
My IC: nRF51822QFAA My SDK Project: ...\nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s110\arm5_no_packs
Appearance：
When I Powerup or...
Hi, I'm having problems flashing the firmware on my Thingy52. I was recently on a course that used another Nordic Semi dev board to connect to the Thingy52 over I2C and use...
Hi. I want to disconect softdevice and ble in order to access to flash memory. I know there are a lot of ways to deal with it. But i want to test to disconect softdevice and...
Good afternoon, Today we had a question about the certification of our product related to the reliability of communication. We received a letter of the following content:...
Hi,
I am trying to update my advertisement data as well as scan response data (i want to put some custom advertisement data and the device name in scan response data). ...
My three buttons are pressed each time, and the LOG information is as follows
0> [00:00:00.000,000] <info> app_timer: RTC: initialized. 0> [00:00:00.000,000] <info> app...
SDK:15.3.0
CHIP:52832
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this...
Hello,
I am developing the following application:
An nRF52840 bluetooth module connected to a sensor does data acquisition and then sends it directly to an nRF52840...
Hi,
I am trying to use SPIM3 to drive LCD(ili9486), but I have encountered some problems, hoping to give me a solution.
I have 2 questions:
1. spi_config.dcx_pin
How...
Hello, we have run the power profiler on two different example projects, and want to understand the difference between the two.
When we run the blinky project
nRF5_SDK_16...
I am buys setting up a project on the NRF52 that needs to use the TWI. Usually I would read byte for byte, and if one of the registers has enough data to justify it, I would...
