Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hello, I am compiling an application to be flashed onto a nRF52810. I am using Segger Embedded Studios and the nRF52 DK to develop the application. I want to read values from...
Hello All,
I have nrf52810 chip. using softdevice 6.1.1
I have implemented dfu feature.
Now i have implement tx power change feature through nrf connect mobile app...
Me and my team have been working for a couple of months on a custom firmware code for nRF9160 on a custom PCB, based on mqtt_simple and asset_tracker which basically reports...
I have been working to get the secure_bootloader examples to run on the NRF52832_XXAB (QFAB with 32kB RAM and 256kB Flash).
Apart from the fact that I had to change the...
Hi,
Good day!
Problem statement:
TSM12 Capacitive touch sensor IC (I2C com supported) is used in our application. It has got 12 output channels and Channel 1 is a parallel...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
Now I am using nrf9160DK for development. In my project, I need to use a random number generator and a highly accurate system time stamp. Is there an API that I can call directly...
Hello,
On nordic nRF9160dk I want to send SMS and receive the data from UART simultaneously. UART needs 3V VDD supply and for Sim card it is 1.8V. So how this condition...
