Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
My application is on the nRF52840 Dongle using ESB protocol, receiving data from an number of PTXs, . The device appears as an HID.
I would like to add Buttonless DFU, without...
Hi,
I am new here and I have some issues with Zigbee reporting implementation.
I am trying to implement a reporting feature between a coordinator and an end device, which...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
Hi all,
since new version of IOS nRF Mesh App I can't finish provisioning of my nRF52840 DK with flashed light example client.
When I start provisioning for the device...
Hi,
I am using NRF52832 with SDK 15.3 and SD 132 on our custom board ( VDD 1.96V ). I started with with the ble_app_template example for our application. Upon measuring...
Hi Nordic
I am using saadc example now, my device output voltage range is -4v~4v.
my saadc config:
VDD: 3.3V
Reference: VDD/4
Gain: 1/4
Mode: SINGLE_ENDE
i got...
Hi, I am new to BLE, I am trying to send and receive data over BLE and print them in Uart as well in both devices respectively.
And I downloaded lastest NRF5-SDK, I have...
Could you, please, direct me to any example (if available) how to manage lost bond with nRF52832/ SDK16 BLE?
Let say very common situation that will try to demonstrate with...
Hi all,
I have hardware as below:
nRF52840-DK - as an advertiser and the same type of board nRF52840-DK - as a scanner
My problem is that I want to send more data than...
Hi,
I have been going through the Bluetooth Course ( https://github.com/NordicPlayground/nRF52-Bluetooth-Course ) and I can' seem to make it work, even if copy/paste the...
Hi,
I'm using nRF51822 to develop our products. I found an interesting problem on our PCB. After I disconnected our PCB from central device, the main function starts from...
I am developing a wearable using nRF52832. I am using SKD_15.3 ble_app_uart source code for testing. And use Putty together. This source code implements UART Baudrate up to...
I have been using fds for flash saving and read. I have used fds_record_write(..) with no errors and proper readings on the just before performing a 4th fds_record_write(...
