[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hi,
Is there any sample code that can check the Ion_idle8 current below?
I am currently evaluating the following currents on a custom boat and it is running at around...
I was wondering how I can update my current code (see below) to reuse a single socket for multiple HTTPS requests, rather than opening and closing a socket for each HTTPS...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
I'm using the nRF52840 and Gazell Pairing (GZP) to develop a device network. Because I need bi-directional communication, I am not using GZP's encryption feature, as it does...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I'm using Zephyr/NCS v2.7.0 with a custom multi-image project based on sysbuild . My top-level project has a sysbuild.conf at the root, and a sysbuild/ folder containing a...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
This ticket is the continuation and related to the previous ticket on the matter: https://devzone.nordicsemi.com/f/nordic-q-a/121669/enabling-the-tls-layer-to-get-a-https...
Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
Hi,
I have a custom board where I have an nrf9161 main processor and an nrf54L05 processor connected with each other via I2C.
In this case, I'd like to manage the communication...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
