Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi
I have a softdevice assert problem when i run the "nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject...
we use
peripheral: exemple ble_app_blinky
central: exemple_ble_app_bliky-c
Instead of a button we have a Switch.
When we set the Switch to "on" the led go on.
That...
Hi, I made a device with using NRF51822, named 'allb' the wearable device for babies.
http://myallb.com
We're planning to make a new version of it with using nRF52840...
The firmware used operate properly in the past, but it no longer does after we replaced the MCU(nrf52832).
During SOFTDEVICE_HANDLER_INIT, the MCU is stopped.
The previous...
I am working on a peripheral. This peripheral is IO display only. On the other side, the central is keyboard + display. I have a single, custom service with a single characteristic...
Hi All,
I did this tutorial : How Import a Keil uVision project Segger Embedded Studio - A Cross Platform IDE ,
but I dont know what did wrong. I still get this error...
While porting my app to the latest 14.0 SDK, it got a little stuck with the new sdh library. I was previously fetching all events through a custom poll & wait loop, but I...
When a packet sent out and get the TX_DS IRQ by nRF24l01+, the mode change to RX and read STATUS register then write the value to the STATUS register and write FLUSH_RX 0xff...
For the SDK13.0.0 the documentation say that HF clock is activated in nrf_drv_usbd_enable() / app_usbd_enable() but it is activated in nrf_drv_usbd_init() / app_usbd_init...
Hi,
We are planning to build a Mobile application for IoT involving Bluetooth communication. We came across a few part numbers of Nordic for this. We would like to know...
I had purchased the Red Bear Labs "Micro" board to develop code using their MK20 USB Dongle and Arduino.
If I "hack" the programming cable to emulate the "Micro" daughter...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
Hello,
I have a question on how to calculate the capacitance based on oscillator relaxation for NRF52. For example, in the Csense_drv example, when pin is touched by finger...
